Search

Search

Home / JUUPINE / 3D Printer Parts & Accessories
2-Pack Upgrade A1mini A1 Hotend Heating Assembly,Hot End Heating Component with Heater Cartridge & Thermistor for Bambu Lab A1 A1mini 3D Printer– Improved Nozzle Clip (No Too Tight/Loose) in Kuwait 2-Pack Upgrade A1mini A1 Hotend Heating Assembly,Hot End Heating Component with Heater Cartridge & Thermistor for Bambu Lab A1 A1mini 3D Printer– Improved Nozzle Clip (No Too Tight/Loose) in Kuwait 2-Pack Upgrade A1mini A1 Hotend Heating Assembly,Hot End Heating Component with Heater Cartridge & Thermistor for Bambu Lab A1 A1mini 3D Printer– Improved Nozzle Clip (No Too Tight/Loose) in Kuwait 2-Pack Upgrade A1mini A1 Hotend Heating Assembly,Hot End Heating Component with Heater Cartridge & Thermistor for Bambu Lab A1 A1mini 3D Printer– Improved Nozzle Clip (No Too Tight/Loose) in Kuwait 2-Pack Upgrade A1mini A1 Hotend Heating Assembly,Hot End Heating Component with Heater Cartridge & Thermistor for Bambu Lab A1 A1mini 3D Printer– Improved Nozzle Clip (No Too Tight/Loose) in Kuwait 2-Pack Upgrade A1mini A1 Hotend Heating Assembly,Hot End Heating Component with Heater Cartridge & Thermistor for Bambu Lab A1 A1mini 3D Printer– Improved Nozzle Clip (No Too Tight/Loose) in Kuwait 2-Pack Upgrade A1mini A1 Hotend Heating Assembly,Hot End Heating Component with Heater Cartridge & Thermistor for Bambu Lab A1 A1mini 3D Printer– Improved Nozzle Clip (No Too Tight/Loose) in Kuwait

2-Pack Upgrade A1mini A1 Hotend Heating Assembly,Hot End Heating Component with Heater Cartridge & Thermistor for Bambu Lab A1 A1mini 3D Printer– Improved Nozzle Clip (No Too Tight/Loose)

KWD 10
Brand
JUUPINE
Weight
50 g
– 1 +

Special Features

  • 1. Precision-Matched Contact Surface – No Thermally Conductive Grease Needed Common complaints: poor surface flatness forces users to apply thermal paste to reach temperature. Our heating block surface is precisely machined for direct, tight contact with the hotend. It heats up normally to 390°C without any grease – just install and print
  • 2. Optimized Clip Fit – Not Too Tight, Not Too Loose, With Tactile Lock Feedback Users often report clips that are either “too tight – need pliers to bend” or “too loose – won't secure”. We strictly control the clip dimensions. A single hand push locks it firmly, with clear tactile feedback. No force required – the hotend stays stable
  • 3. Reinforced Cable Root – Resists Breakage During Maintenance Frequent complaint: “The cable snapped at the root when cleaning a blob, ruining the whole assembly.” We reinforced the connection point between the connector and cables to improve tensile strength. It withstands normal maintenance handling, reducing premature failure
  • 4. Factory-Tested Thermistor – Stable Temperature Reading, No Glitches Many users report erratic readings (0°C, random jumps, or unable to boot after replacement). Each unit is tested before shipping – NTC thermistor resistance (~100kΩ at room temperature) and heater resistance (~7Ω) are verified. You get correct temperature readings, no “showing 300°C but not heating” issues
  • 5. 2-Pack = Backup Ready – Minimize Downtime Heating assemblies are consumables and usually not covered by warranty. This kit includes two complete heating assemblies (heater cartridge, thermistor, heat break, heating block). Use one, keep one as a spare. When a clog or wear occurs, swap in the backup immediately – no waiting for shipping. Compatible with both A1 and A1 Mini

Description

2-Pack A1 / A1 Mini Heating Assembly This product is a drop-in replacement heating assembly designed for Bambu Lab A1 and A1 Mini 3D printers. Each assembly includes a heater cartridge, NTC thermistor, stainless steel heat break, and heating block. The pack contains two complete assemblies. No soldering or part salvaging is required. Product Features The heating block features a precision-machined contact surface for direct installation. The clip is designed with controlled dimensions and locks with a single hand push, providing tactile feedback for secure locking. The connector and cables are reinforced at the connection point to improve tensile strength Two assemblies are included per pack. Specifications Compatibility: Bambu Lab A1 and A1 Mini (and other A1 series with same connector) Maximum Temperature: 300°C Supported Filaments: PLA, PETG, ABS, TPU, and others Installation: Direct replacement, no printer modification required Package Contents Heating Assembly × 2 sets Note: Silicone socks and nozzle/hotend are not included. Ideal For Replacing a clogged or worn heating assembly Replacing a failed heater cartridge or thermistor Keeping a backup assembly to reduce downtime If you have any questions about compatibility or installation, please contact us before purchase.

Related Items

{"error":"Error","cart_limit":"You have too many items in your cart.","prod_limit":"You cannot add any more of this item"}