Compatible With MATEK M10Q-5883 20X20mm GNSS GPS Module / Compass QMC5883L Compatible With RC Airplane Freestyle Long Range Drones DIY Parts

Specifications
GNSS Compatible With u b x SAM-M10Q (Compatible With GPS, Compatible With GLONASS, Compatible With Galileo and Compatible With BeiDou)
/ Compass QMC5883L
Patch ant 15*15*4mm
Input voltage range: 4~9V (5V pad/pin)
Power consumption: 13mA
Compatible With UART baudrate: 9600 default
Operating Temperatures: -20~80 °C
Compatible With UART(Compatible With TX, Compatible With ) interface Compatible With GNSS SAM-M10Q-00B
I2C(DA, CL) interface Compatible With Compass QMC5883L
Compatible With JST-GH-6P connector (SM06B-GHS-TB). 1.27mm pitch
GNSS PPS , Green. (Solid ON after powering on, blinking(1Hz) when GNSS get 3D fix)
Protocol: Compatible With U B X
5Hz@GPS+GAL+BDS B1C+GLO or NMEA 1Hz
20mm*20mm*12.4mm
8g
M10Q-5883_step.zip
Includes
1x M10Q-5883
1x Compatible With JST-GH-6P to Compatible With JST-GH-6P 20cm silicon wire
Wiring and settings
M10Q-5883 5V to Flight controller 4~9V
M10Q-5883 to Flight controller UART_TX
M10Q-5883 TX to Flight controller UART_RX
M10Q-5883 CL to Flight controller I2C_SCL
M10Q-5883 DA to Flight controller I2C_SDA
M10Q-5883 G to Flight controller GND

Tips and Notes
Compass Alignment(flat mounting): Tilting the magnetometer is strongly discouraged !
Compatible With INAV/For BetaFLight: compass Arrow forward, set CW 270° Flip when flight controller arrow is facing forward.
Compatible With INAV/For BetaFLight: compass Arrow backward, set CW 90° Flip when flight controller arrow is facing forward.
Compatible With Ardupilot/Mission Planner: Rotation None.
Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron based material
------

Compatible With INAV 5.0.0, Compatible With Betaflight 4.3.0, Compatible With ArduPilot 4.3 or newer is required.
Compatible With U B X NEO-M9N, MAX-M10S, SAM-M10Q series all don't have dataflash built in. once GNSS is powered off and the supercapacitor run out. the settings will back to default.
Compatible With U B X protocol is bidirectional. Flight controller firmware can change settings on GPS via Compatible With U B X protocol. You don't need to set GNSS module parameters in u-center.
The default configuration on SAM-M10Q with Compatible With u b x FW 5.1 is concurrent reception of GPS, Compatible With Galileo, Compatible With GLONASS, and Compatible With BeiDou B1C with Compatible With QZSS and SBAS enabled.
Start with Compatible With u b x GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take to 12.5 min. Probably PPS will not blink immediately after GPS has 3D fixed.
The M10Q-5883 provides the ability to reset the receiver. Bridging "RST" pad to Ground Compatible With at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but flight controller can't detect the GNSS module(grey GPS icon), try doing reset.
The scratches on ceramic ant are the result of tuning the ant.
*** The SKU silk print on the first batch of M10Q-5883 PCB is "M10-5883".