Speed Control
High performance high current scr controller 180v 220v motor speed control 20A
Model: 220DR20AL
High Current Controller Description:
MMT-220DR serial motor speed controller adopts SCR chopper, which has unique trigger mode, thus making it more accurate and reliable. The drive is the update speed regulation product which develops and produces in combination with the international standard requirements and absorbs advanced technology experience. The drive has high performance-cost ratio because of its excellent performance and reliable quality. (It can high speed ratio even when at non-speed feedback) It is above average in motor drive field. Currently, the serial products have been exported to many countries and widely used in fields of domestic plastics machinery, food machinery, cable equipment, mechanical processing, papermaking, printing, experimental equipment, laboratory equipment, mixing equipment and so on.
Brushed Controller Features:
1. SMT technology, Small volume brushed motor speed controller
2. Applicable to permanent-magnet motor, separate excitation motor and motor
3. Dual closed loop PI adjustment (Current and Voltage)
4. Current setting and current limiting protection
5. The speed control mode and expansive force control mode are selectable.
6. Large for low-speed start-up.
7. Quick stop function
8. Upper limit and Low limit can be set up to different need
9. ACCEL and DECEL function
10. Standard signal interface 0-5V or 10K potentiometer
11. Can realize remote start and stop, Fine following performance; immediate dynamic response
12. A wide speed-regulating range (0 - max).
13. Strong mechanical features, static voltage error 1%
14. A rapid dynamic response process.(adjustable)
15. Automatic and smooth transition process during acceleration or deceleration.
16. Good excavator features, can automatically overload current limit on the current settings.
17. High reliability, compact structure and highly cost-effective.
180V 220V High Power Controller Parameter:
1. Input voltage range: AC 220V
2. Output Armature Voltage: 0-90V 0-110V 0-160V 0-180V 0-220V (you can adjust the output voltage by yourself.)
3. Max output current: 20A
4. Operating mode: Speed mode, Tension mode ( mode)
5. Control ways: Potentiometer, 0-5V (if you need 0-10v control, please leave a message)
6. Protection: Abnormalitise like over current, overheating, over voltage, less voltage and short circuit will start the protection function.
7. Soft start /stop time: 0.2s - 20s
8. Size: L*W*H = 154*135*85 mm
8. Weight: 1250g
Motor Speed Controller Picture:
Soft Start Controller Connect Drawing:
Enable control: INHIBIT
Control the motor Start and Stop
180V motor speed control signal:
1. The serial products adopt the full isolation mode and the external given signal can connect directly with the signal input terminal of drive.
External potentiometers and analog signals for a given amount of signal for a given connection method
2. Several potentiometer series / parallel usag
Means a potentiometer in parallel: This control mode enables two or more to adjust, use is simple and reliable. However, the total potentiometer resistance should be equal to 10K. (Potentiometer connection is best to use shielded line)
3. Resistors in series connection
This control method can achieve multi-stall speed control, used in a variety of occasions. However, the total resistance of resistors in series shown in the picture be equal to 10K.
130V motor controller Internal potentiometer definition:
Notice: Clock wise rotation to increase, anticlockwise rotation to decrease.
1. MAX SPD
Adjust the MAX SPD potentiometer to limit the motor maximum speed. that means you can adjust the controller output voltage via this potentiometer. clockwise the potentiometer to increase the output voltage.
2. MIN SPD
Adjust the MIN SPD potentiometer to limit the motor minimum speed.
3. ACCEL Soft-start time adjustment
This adjustment of potentiometers ACCEL can make sure motor's rising slope from the initial velocity up to the highest velocity (that is rising time, set time adjustable during 0-20 seconds).
4. Soft-stop time adjustment (The interior has been fixed): DECEL
Adjustment of potentiometers DECEL can make sure motor's decline slope when speed dropped from the highest to the lowest (that is falling time, set time adjustable during 0-20 seconds).
5. Current limit adjustment: (when Under speed mode condition ) Adjustment of the potentiometer can restrict drive plate to a maximum output current.
Based on your selection of the motor's rated current, we can use this potentiometer to adjust driver output current to match the motor rated current.
Note: In the choice of driver, the driver's maximum output current should be 120% to 200% of motor rated current.
6. compensation adjustments: IR COMP
Adjust this potentiometer can keep a constant rotation speed when motor works in different load.
Speed mode and Tension mode selection:
1. Selection of speed mode:
2. Selection of tension mode:
Rapid braking (dynamic braking) of the connection:
Note: When using this method when braking (dynamic braking) Please be sure to enable the port used in conjunction with, otherwise it will damage the bruhsed controller.
This control method can obtain good braking effect. Braking resistor selection:
RW (braking resistor power) = motor actual power X (0.6-0.8)
R (braking resistor resistance) = Rated Voltage / (rated current X 1.2)
Forward / Rreverse:
Note: When using this method when braking (dynamic braking) Please be sure to enable the port used in conjunction with, otherwise it will damage the controller.
high performance high current scr controller 180v 220v motor speed control 20A
Related products
Model
Input voltage
Output voltage
Continue current
Max current
Controller mode
220DR15AL
AC 220V
0-90V, 0-110V, 0-160V,
0-180V, 0-220VDC
8A
15A
Poti, 0-5V
220DR20AL
AC 220V
0-90V, 0-110V, 0-160V,
0-180V, 0-220VDC
10A
20A
Poti, 0-5V
220DR35AL
AC 220V
0-90V, 0-110V, 0-160V,
0-180V, 0-220VDC
18A
35A
Poti, 0-5V
==========
Model Number : 220DR20AL
Motor Type : Motor
Input voltage : 220VAC
Output voltage : 0-130V, 0-180V, 0-220V
Max current : 20A
Control signal : Potentiometer, 0-5V
Soft start : 0.2s- 20s
Soft stop : 0.2s - 20s
Operation mode : Speed mode, Tension mode
Matched motor : brushed motor, pmdc motor, separated excited motor